- Description
- Product Details
- Additional Information
Description
NI000210_76997648 - Details
| Form Name | Foil |
| Thickness | 0.0025mm |
| Purity | 99.95% |
| Condition | Electrodeposited |
| Size | 148x300 mm |
Product Details
Form information
Bar
A straight length of rectangular, square or oval section material.
| Tolerances | ||||
| Section dimensions: | =<10mm | ±10% | >10mm | ±1mm |
| Length: | <100mm | ±1mm | >=100mm | +5%/-1% |
Bolt
A threaded pin that can be screwed into a nut or a tapped hole to fasten items together. Bolts are available with different head styles and also in metric and inch-threaded sizes.
| Tolerances | |
| Ceramics: | ANSI B18.6.7M-1985 |
Chopped Fibre
Fibres cut into short lengths called cut, staple or chopped fibre.
| Tolerances | |
| Fibre diameter: | ±25% |
| Number of strands: | ±10% |
| Tex number: | ±10% |
| Length: | +5%/-1% |
Crucible
A vessel in which other materials may be heated or melted, usually at high temperatures.
| Tolerances | |
| Height: | ±10% |
| Wall Thickness: | ±10% |
| Outside Dimensions: | ±10% |
Fabric
Woven fabrics are made by the regular interlacing of two arrays of yarns at right angles to each other, these being referred to as the warp and weft (see also Non-woven fabric)
| Tolerances | ||||
| Fabric thickness: | ±25% | |||
| Number of yarns: | ±10% | |||
| Tex number: | ±10% | |||
| Size (linear dimension): | <100mm | ±5mm | >=100mm | ±5% |
Fibre
Yarns or tows consisting of several approximately parallel individual filaments, each filament usually being smaller in diameter than a monofilament.
| Tolerances | |
| Fibre diameter: | ±25% |
| Number of strands: | ±10% |
| Tex number: | ±10% |
| Length: | ±5% / -1% |
Film
A non-metallic sheet material with a thickness <0.5mm.
| Tolerances | ||||
| Thickness: | ±20% | |||
| Size (linear dimension): | <100mm | ±1mm | >=100mm | +2%/-1% |
Flake
Flat, irregularly shaped pieces of material. A maximum flake size is indicated, but individual flakes may vary greatly in size.
Tolerances: Dimensions shown are nominal
Foam
A low density, permeable structure of cells and continuous ligaments offering a high surface area to volume ratio, and also a high strength to weight ratio. Owing to the nature of this material, dimensions are nominal.
Foil
Thin sheets of pure metal and metal alloys. Due to their fragile nature, some foils are coated on one side with an acrylic or polyester support. Where foils are supported they are indicated in the detailed item description.
Light Tight Foil: LT Foils are supplied without visible pinholes whereas NLT foils will normally contain pinholes, but may occasionally be free from pinholes. Foils 0.025mm or more in thickness are supplied LT unless otherwise stated. Foils less than 0.025mm are normally supplied NLT, however, if you require LT foils, please ask. An additional charge may be made if we are able to supply LT foils.
| Tolerances | ||||
| Thickness: | <0.010mm | ±25% | ||
| 0.010-0.050mm | ±15% | |||
| >0.050mm | ±10% | |||
| Size (linear dimension): | <100mm | ±1mm | >=100mm | +2%/-1% |
Granule
Pellets of an approximately regular shape. Granules may vary in size and, therefore, the dimensions stated are nominal. In addition, the shape of a granule may vary from item to item.
Tolerances: Dimensions shown are nominal.
Honeycomb
A cellular structure similar in appearance to natural honeycomb. Owing to the nature of this material, dimensions are nominal.
Insulated Wire
A single or multiple flexible strand of metal or alloy with an insulating sheath.
| Tolerances | |
| Wire diameter: | ±10% |
| Length: | ±5%/-1% |
Insulation thickness: Nominal values only
Laminate
Layers of material which have been bonded together by the use of heat, pressure and, possibly, adhesive.
| Tolerances | ||||
| Thickness: | ±10% | |||
| Size (linear dimension): | =<100mm | ±1mm | >100mm | ±2%/-1% |
Liquid
A state of matter between a solid and a gas in which the shape of a given mass depends on the container, the volume being independent.
Lump
A solid piece of material with no defined shape.
Tolerances: Dimensions shown are nominal
Mesh
Mesh is available as either a woven wire or electroformed product; in all cases, the quoted aperture sizes are nominal. Wire mesh: a material which is woven from metal wires to provide a thin grid with a regular series of holes. Electroformed mesh: a product made by electroplating the mesh geometry through a mask onto a substrate which is subsequently etched away.
| Tolerances | ||||
| Thickness: | woven: | ±10% | electroformed: | ±20% |
| Wire diameter: | ±10% | |||
| Size (linear dimension): | <100mm | ±1mm | >=100mm | +2%/-1% |
Metalised Film
Film which is coated with a metal. The thickness of the metal is measured and described in terms of the material's specific electrical resistance in ohms per square.
| Tolerances | ||||
| Thickness: | ±10% | |||
| Size (linear dimension): | <100mm | ±1mm | >=100mm | +2%/-1% |
Microfoil
An extremely thin sheet of metal or alloy mounted on a permanent support. This support cannot be removed without destroying the Microfoil.
| Tolerances | |
| Thickness: | ±30% |
| Size: | ±20% |
Microleaf
An extremely thin sheet of metal mounted on a removable support. Microleaf is not available for metals which are too brittle to be free standing. Microleaf is mounted on a specially treated support which allows separation of the metal film from the support. Full instructions on the method of removal are issued with each Microleaf supplied.
| Tolerances | |
| Thickness: | ±30% |
| Size: | ±20% |
Monofilament
A single strand of a non-metallic material.
| Tolerances | |
| Diameter: | ±20% |
| Length: | +5%/-1% |
Non-Woven Fabric
Non-woven fabrics are made by methods other than weaving or knitting, the yarns and fibres being held together, often quite loosely, by means other than geometric interlacing. Due to the open and porous nature of this material, all other dimensions are nominal.
| Tolerances | ||||
| Size (linear dimension): | <100mm | ±5mm | >100mm | ±5% |
Nut
Generally a flat piece of material with a threaded hole which can be screwed onto a bolt to fasten items together. Nuts typically have a hexagonal external shape. Nuts are available in metric and inch-threaded sizes.
| Tolerances | |
| Ceramics: | ANSI B18.2.4.1M-1979 (R1995) |
Powder
Small particles with an approximately defined size range. Those materials described as alloy precursors are not true alloys - they are made by sintering a blend of powders of the component metals to achieve alloying by diffusion. The resultant cake is ground and sieved to the required particle size range. Unless otherwise stated, the particle sizes shown are for guidance only. We do not guarantee either any particular size distribution between the quoted minimum and maximum sizes, or a specific particle shape.
Tolerances: Dimensions shown are nominal
Rod
A straight length of circular section material.
| Tolerances | ||||
| Diameter: | <10mm | ±10% | ||
| Polymer | ±20%/-10% | |||
| Ceramic | ±20%/-10% | |||
| >10mm | ±5% | |||
| Polymer | ±20%/-10% | |||
| Ceramic | ±20%/-10% | |||
| Length: | <100mm | ±1mm | >=100mm | +5%/-1% |
Sheet
Flat material with a thickness >0.5mm.
| Tolerances | ||||
| Thickness: | ±10% | |||
| Ceramic | ±20% | |||
| Composite | ±20% | |||
| Polymer | ±20% | |||
| Size (linear dimension): | <100mm | ±1mm | >=100mm | +2%/-1% |
Single Crystal
A material grown as a monocrystal, generally to a specific orientation, dimension and surface finish. It may contain a dopant. Single crystals are usually made to order.
| Tolerances | |
| Orientation: | ±3° |
Size: Sizes shown are nominal
Sphere
Small balls which are precision ground.
| Tolerances | |
| Diameter: | ±5% |
Sputtering Target
A high purity material used as a source for sputtering, a cold vapourisation process in which atoms are physically removed from the target surface by ion bombardment.
| Tolerances | |
| Thickness: | ±5% |
| Size: | ±5% |
Tube
A hollow length of material normally circular in section. Most tubes are straight except those made of flexible polymer.
| Tolerances | ||||
| Outside Diameter: | <2mm | ±0.05mm | ||
| Polymer | ±10% | |||
| Ceramic | ±10% | |||
| =<5mm | ±0.1mm | |||
| Polymer | ±10% | |||
| Ceramic | ±10% | |||
| =>5mm | ±5% | |||
| Polymer | ±10% | |||
| Ceramic | ±10% | |||
| Wall Thickness: | ±10% | |||
| Polymer | ±20% | |||
| Ceramic | ±20% | |||
| Length: | <100mm | ±1mm | >=100mm | +5%/-1% |
Washer
A thin, flat piece of material with a hole in the middle, used in conjunction with bolts and nuts to distribute the load of a threaded fastener.
| Tolerances | |
| Ceramics: | ANSI B18.22M-1981, R1990 (Reg) |
Wire
A single or multiple flexible strand of pure metal or alloy.
| Tolerances | |
| Wire diameter: | ±10% |
| Length: | +5%/-1% |
Additional Information
Goodfellow Introduction
Goodfellow is well known as a specialist supplier of metals, alloys, ceramics, polymers and other materials, with no minimum order quantity, to meet the research, development and specialist production requirements of science and industry worldwide.The range of materials offered by Goodfellow is extensive as are the forms in which the various products are available.
Materials
Metals and Alloys
Goodfellow supplies virtually all of the pure metals from Aluminium to Zirconium as well as a comprehensive range of alloys. Most are available in a variety of forms, including rod, wire and foil. The on-line catalogue details those materials which are available as standard products from stock. Custom-made items are also available, so please contact us if you are unable to identify the item you require.
Ceramics
The ceramic materials offered by Goodfellow have been carefully chosen and include both the established, as well as more recently developed products. All are available as either standard or custom-made products in a variety of forms and sizes. The on-line catalogue details those items which are available from stock; please contact us if you are unable to find the specific item you require.
Glasses
Goodfellow offers two distinct types of glass products; silica-based, non-crystalline (amorphous) solids and non-crystalline (amorphous) ""metallic glasses"" or ""glassy metals"". The majority of these items are made to order. Please contact us with details of your requirements.
Polymers
The range of polymers supplied by Goodfellow is broad and includes both the familiar as well as some of the more unusual or recently developed materials. The on-line catalogue details those items which are available from stock; please contact us if you are unable to find the item you specifically require.
Compounds & Intermetallics
Goodfellow can supply aluminides, borides and silicides as well as other intermetallics and compounds. The majority of these items are made to order and the on-line catalogue details those which are available. Please contact us with details of your requirements.
Composites
Some examples of these materials are listed in the on-line catalogue. As some of these are manufactured on a custom-made basis, please contact us with details of your requirements.